Most people are familiar with the standard Samsung TV remote. However, you may not know how to open it up to change the batteries. The process is actually quite simple and only takes a few minutes.
Here’s how you do it: Start by locating the small tab on the back of the remote. This is usually located near the bottom left corner.
Gently pry up on this tab with your fingernail or a small flathead screwdriver. Once the tab is raised, you should be able to see two small pins inside the battery compartment.
If you have a Samsung TV, chances are good that you also have a Samsung remote.
Here’s how to open it up and change the batteries:
- Start by finding the release button on the back of the remote.
It should be located near the top. - Press and hold the release button down while simultaneously sliding the front cover off of the remote.
- Once the front cover is off, you’ll see two batteries inside.
Remove them both and then insert new ones in their place, being sure to observe correct polarity (+/-). - Replace the front cover and press the release button to snap it back into place. Your remote is now ready for use!
How Do You Open Samsung TV Remote?
Assuming you would like tips on how to open a Samsung TV remote: If your Samsung TV remote has a cover over the batteries, start by removing that. Use a small Phillips head screwdriver to remove any screws holding the battery cover in place.
Once the screws are removed, gently pry off the battery cover. Remove the old batteries from the remote and dispose of them properly.
Insert new batteries into the remote, making sure they are inserted correctly according to the + and – symbols inside the battery compartment.
Once the new batteries are inserted, reattach the battery cover and screw it back into place. Your Samsung TV remote should now be working properly!
How Do You Take the Back off a Samsung Remote?
Assuming you would like tips on how to open the back cover of a Samsung TV remote:
- Locate the seam that runs along the back of the remote. This is where the two halves of the casing meet.
- Insert a thin object, like a nail file or a flathead screwdriver, into the seam and pry gently until the back cover pops off.
- If your remote has batteries, they will likely fall out when you remove the back cover. Inspect the batteries and, if necessary, replace them with new ones before putting the cover back on.
How Do I Open My Remote Control?
Assuming you are referring to a TV remote: There are several ways to open a TV remote, depending on the model. The most common is to use a coin or other small object to press in the tab located on the back or side of the remote.
This will release the battery compartment door so you can access the batteries. Some models also have a screw that needs to be removed before the battery compartment can be accessed.
How Do You Put a Battery in a Remote?
If your remote control needs a new battery, you can easily replace it yourself. All you need is a small Phillips head screwdriver and a fresh AAA or AA battery.
Here’s how to do it:
- Find the screws on the back of the remote. There are usually two of them, and they’re located near the bottom of the remote.
- Use the Phillips head screwdriver to unscrew those two screws.
- Carefully remove the back of the remote control (the part with the batteries). Be careful not to lose any of the small parts inside, like springs or washers.
- Take out the old batteries from their compartments in the back of the remote control unit.
Make note of which way they were facing so you can put in new batteries correctly (+/-). - Put in fresh AAA or AA batteries, again making sure to put them in correctly according to their +/- symbols.
How to Open Samsung Smart TV Remote 2015
If you have a Samsung Smart TV from 2015 or later, then you can use the Samsung Smart Remote that comes with it. If you don’t have this remote, don’t worry – you can still use your TV.
Just follow these simple steps:
- On your TV, go to Settings > General > External Device Manager > Samsung Smart Remote Control.
- Press and hold the Select button on your remote for 3 seconds. The LED will blink twice to indicate that the remote is in pairing mode.
- On your smartphone, open the Samsung Smart Remote app and follow the on-screen instructions to pair your devices.
- Once paired, you’ll be able to control your TV using the app.
Conclusion
If you need to know how to open a Samsung TV remote, there are a few things that you will need to do.
First, you will need to locate the release button on the back of the remote. This button is usually located near the batteries.
Once you have found the release button, you will need to press and hold it down for a few seconds.
After a few seconds have passed, the back cover of the remote should come off easily.
