If you want to factory reset your TP-Link extender, you will need to press and hold the reset button for at least 10 seconds. The reset button is usually located on the back of the device. Once the extender has been reset, it will be restored to its default settings.
- Unplug the TP-Link extender from the power outlet
- Press and hold the reset button on the back of the device for 5 seconds
- Plug the TP-Link extender back into the power outlet
- The TP-Link extender will now be reset to its default factory settings
How Do I Connect My Tp-Link Extender to a New Network?
If you’ve recently switched to a new router or changed your network’s name and password, you’ll need to reconnect your TP-Link extender to the new network. Here’s how:
1. Unplug your TP-Link extender from the power outlet and plug it back in.
2. When the Power LED is solid green, press and hold the WPS button on your extender for 5 seconds.
3. Within 2 minutes, press the WPS button on your new router or access point.
4. The Extender Connection / WPS LED will turn solid green when the connection is successful.
5. Once connected, open a web browser and enter tplinkrepeater.net into the address bar to access the extender’s management page (the default username is admin).
6. On the management page, go to Wireless > Wireless Settings and verify that both the SSID (network name) and password are correct for your new network. If they’re not, update them accordingly and click Save at the bottom of the page.
That’s it! Your TP-Link extender should now be successfully connected to your new network.
Note: If you’re still having trouble connecting your TP-Link extender to your new network, try restarting both devices (extender and router/access point) and repeating Steps 2-6 above.
How Do I Reset My Tp-Link Extender Re200?
If you need to reset your TP-Link extender, there are a few different ways to do it. One way is to use the reset button on the back of the unit. This will reset the extender to its factory defaults.
Another way is to log in to the extender’s web interface and go to the System Tools > Restore Default Settings page. This will also reset the extender to its factory defaults.
How Do I Setup My Tp-Link Router After Factory Reset?
If you need to reset your TP-Link router, there are a few different ways that you can do it. In this article, we’ll show you how to factory reset a TP-Link router through the web interface and via the buttons on the device. Resetting your router to its factory default settings is usually only necessary if you’ve forgotten your password or if you’re troubleshooting an issue.
Once you reset the router, all of your customizations will be lost and it will be back to its original state. Before resetting your router, make sure to back up any important settings or configurations that you don’t want to lose. Once you’ve backed up your data, follow these steps to reset your TP-Link router:
Web Interface Reset:
1. Log into the web interface of your TP-Link router. The default address is typical http://192.168.0.1/.
If that doesn’t work, check the documentation for your specific model number.
2. Go to System Tools > Factory Defaults > Restore Factory Defaults > Restore button.
3. A pop-up window will appear asking if you’re sure that you want to restore the factory defaults; click OK.
Hard Reset (Button):
1) Locate the RESET button on the back of your TP-Link router
2) Use a paperclip or other sharp object to press and hold down the RESET button for about 10 seconds
3) Release the RESET button and wait for the device to reboot; this may take a few minutes
How to Reset Tp-Link Extender Password
If you have forgotten your TP-Link extender password, don’t worry! You can easily reset it using the following steps: 1. Connect to your TP-Link extender via Ethernet or Wi-Fi.
2. Open a web browser and enter www.tplinklogin.net in the address bar.
3. Enter your username and password (the default username is admin).
4. Click on System Tools > Factory Defaults.
5. Click on the Restore button to reset your TP-Link extender to factory defaults.
Conclusion
If you’re experiencing problems with your TP-Link extender, one thing you can try is resetting it to factory settings. This will erase all of the customizations you’ve made, but it can sometimes fix issues. Here’s how to do a factory reset on your TP-Link extender:
1. Unplug the extender from the power outlet and then plug it back in.
2. Press and hold the Reset button for at least 10 seconds. The Status light should start blinking when you first press the button, and then it will turn solid once the reset is complete.
3. Once the reset is finished, your extender will go back to its default settings. You’ll need to reconfigure it before you can use it again.
